The circuit breaker plug of our house does not have any kind of device in it, but it gets tripped. We all wonder what could be the main reason behind this. So let me tell you that this question is not for you but for many people. Many of us must have experienced power tripping. Circuit tripping can occur in a number of ways, from overloading to short circuits or other minor problems.
If there is a similar problem in our house, even if it is tripping with or without load, first disconnect the load attached to it and set the circuit breaker again. Then the chances of this trip decrease. However, if this problem persists, the solution to your tension is in today’s article.
Common reasons your breaker keeps tripping include circuit overload, a short circuit, or a ground fault.
Suggested Read: What Is an Oil Circuit Breaker | Construction of Oil Circuit Breaker
Reasons Your Circuit Breaker Keeps Tripping with Nothing Plugged In:
Every time a circuit breaker trips, the first question on everyone’s mind is the same. This overload may have caused the trip, but it does not happen. This is possible. But with the exception of the case, there could be many reasons behind this. These causes of circuit breaker trips are described in detail below, and how they can be resolved is discussed in detail.
First of all, the reason for his trip is as follows:
| Sr. No. | Circuit Breaker Trips Without Load |
| #1. | Short Circuit |
| #2. | Overcurrent |
| #3. | Ground Fault |
| #4. | Faulty Circuit Breaker |
#1. Short Circuit:
The short circuit is the factor that shuts down the circuit breaker. The reason behind this is when the hot wire and the neutral pull. The contact causes a high current to flow through the circuit, which is greater than the capacity of the circuit. Generates more heat than that.
When this happens, the breaker wire departs to avoid burning and damage to electrical equipment. There can be many reasons for short circuits in the home or office, or factory. A major cause, such as a faulty wiring system or a weak joint, can cause short circuits.
Troubleshooting a short circuit requires your sensory organs, such as the nose and eyes, which you can use to identify the area affected by a short circuit with a burning smell and correct the error. But as an engineer, we have one piece of advice. This work should be done by a knowledgeable electrician rather than yourself. Because if you do this work yourself, there is a possibility of shock.
#2. Overcurrent:
Most circuit breakers are not thermal types. And thermal circuit breakers travel current. When there is a high current. It hits the bi-metallic metal of the circuit breaker until it heats up and does not heat up.
The main causes of overload include ground fault, overload, faulty arcs, faulty wiring, short circuits, fuses, and others. Whenever there is an overload problem, and it is your turn to work on the current line, you need to contact a suitable electrician.
#3. Ground Fault:
Ground fault and earth fault have the same meaning, and this fault is the same as a short circuit. This is the main cause of the fault when any hot wire comes in contact with the earthing wire. And it carries more current than the contact circuit, which causes this circuit to trip the breaker. In case of a ground fault, it is necessary to consult a suitable electrician. To avoid complications that may arise from doing it yourself.
#4. Faulty Circuit Breaker:
Trips can also be made when the circuit breaker in our home or office has broken down. If its power failure is due to a weak circuit breaker, So it is advisable to change it to avoid complications.
Suggested Read: Different Types of Faults and Effects in Electrical Power Systems
Reasons Your GFCI Breaker Keeps Tripping with Nothing Plugged In:
GFCI stands for obstruction of ground fault circuit. If your GFCI is tripping, then the error is yours. In general, the light of travel follows its path. But if, for some reason, it follows a different path towards the ground, the ground will fault.
The main cause of the ground fault is when there is contact between a live wire and water or wet material. This causes the current to flow with the water. Ground faults can lead to electrocution in buildings without ground fault circuit interrupters (GFCI). But if you have interrupters, it will turn off the light without delay.
My Light Went Out, but the Circuit Breaker had Not Tripped; why?
Some circuit breakers act like what is called a trip-free circuit breaker. The trip-on circuit breaker switches off the light. This works best on circuits that do not face overcurrents. If you experience a free trip, call your electrician for troubleshooting.
How Do You Know If a Circuit Breaker Has Tripped?
If our lights were turned off in only one room in the whole house, we could estimate that the circuit breaker had tripped.
We can also tell by looking at the breaker switch whether it is on or off. Although some types of circuit breakers (travel-free) occur when there is no light, however, using one of the two methods can help you locate a stranded breaker.
How to Reset a Tripped Circuit Breaker?
To reset the tripped circuit breaker, turn it off. Disconnect all devices connected to this circuit from the plug and then turn on the circuit breaker. The reason for our safety is that we are told to stand away from the circuit breaker while resetting it.
Goggles must be used for eye safety, And if it is dark at work, you must use a torch. After resetting the circuit breaker, wait a while before connecting any device to it, and make sure you do not overload the circuit.
Like this post? Could you share it with your friends?
Suggested Read –
Very interested
thanks